收藏本站
VISHAY SILICONIX
TrenchFET ? Power MOSFETs
Application Note 808
Mounting LITTLE FOOT ? , SO-8 Power MOSFETs
Wharton McDaniel
0.2 88
Surface-mounted LITTLE FOOT power MOSFETs use
integrated circuit and small-signal packages which have
7.3
been been modified to provide the heat transfer capabilities
required by power devices. Leadframe materials and
design, molding compounds, and die attach materials have
been changed, while the footprint of the packages remains
the same.
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
0.050
1.27
0.027
0.69
0.07 8
1.9 8
0.2
5.07
0.0 88
2.25
0.0 88
2.25
MOSFETs, ( http://www.vishay.com/ppg?72286 ), for the
basis of the pad design for a LITTLE FOOT SO-8 power
MOSFET. In converting this recommended minimum pad
to the pad set for a power MOSFET, designers must make
two connections: an electrical connection and a thermal
connection, to draw heat away from the package.
In the case of the SO-8 package, the thermal connections
are very simple. Pins 5, 6, 7, and 8 are the drain of the
MOSFET for a single MOSFET package and are connected
together. In a dual package, pins 5 and 6 are one drain, and
pins 7 and 8 are the other drain. For a small-signal device or
integrated circuit, typical connections would be made with
traces that are 0.020 inches wide. Since the drain pins serve
the additional function of providing the thermal connection
to the package, this level of connection is inadequate. The
total cross section of the copper may be adequate to carry
the current required for the application, but it presents a
large thermal impedance. Also, heat spreads in a circular
fashion from the heat source. In this case the drain pins are
the heat sources when looking at heat spread on the PC
board.
0.2 88
7.3
0.050
1.27
0.196
5.0
0.027
0.69
Figure 2. Dual MOSFET SO-8 Pad Pattern
With Copper Spreading
The minimum recommended pad patterns for the
single-MOSFET SO-8 with copper spreading (Figure 1) and
dual-MOSFET SO-8 with copper spreading (Figure 2) show
the starting point for utilizing the board area available for the
heat-spreading copper. To create this pattern, a plane of
copper overlies the drain pins. The copper plane connects
the drain pins electrically, but more importantly provides
planar copper to draw heat from the drain leads and start the
process of spreading the heat so it can be dissipated into the
ambient air. These patterns use all the available area
underneath the body for this purpose.
Since surface-mounted packages are small, and reflow
soldering is the most common way in which these are
affixed to the PC board, “thermal” connections from the
planar copper to the pads have not been used. Even if
additional planar copper area is used, there should be no
problems in the soldering process. The actual solder
connections are defined by the solder mask openings. By
combining the basic footprint with the copper plane on the
drain pins, the solder mask generation occurs automatically.
A final item to keep in mind is the width of the power traces.
The absolute minimum power trace width must be
determined by the amount of current it has to carry. For
0.07 8
1.9 8
0.2
5.07
thermal reasons, this minimum width should be at least
0.020 inches. The use of wide traces connected to the drain
Figure 1. Single MOSFET SO-8 Pad
Pattern With Copper Spreading
Document Number: 70740
Revision: 18-Jun-07
plane provides a low impedance path for heat to move away
from the device.
www.vishay.com
1
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI4134DY-T1-E3 MOSFET N-CH D-S 30V 8-SOIC
SI4158DY-T1-GE3 MOSFET N-CH D-S 20V 8-SOIC
SI4170DY-T1-GE3 MOSFET N-CH 30V 30A 8-SOIC
SI4174DY-T1-GE3 MOSFET N-CH D-S 30V 8-SOIC
SI4186DY-T1-GE3 MOSFET N-CH 20V 35.8A 8SOIC
SI4190ADY-T1-GE3 MOSF N CH 100V 18.4A SO8
SI4214DDY-T1-E3 MOSFET 2N-CH 30V 8.5A SO8
SI4214DY-T1-GE3 MOSFET N-CH D-S 30V 8-SOIC
相关代理商/技术参数
SI4126-F-BM 功能描述:射频无线杂项 WLAN SYNTHSIZER MLP-28 RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
SI4126-F-BMR 功能描述:IC SYNTHESIZER RF2/IF 28MLP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,140 系列:AU 类型:收发器 驱动器/接收器数:1/1 规程:CAN 电源电压:5.3 V ~ 27 V 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:管件 其它名称:935267940512AU5790D14AU5790D14-ND
SI4126-F-GM 功能描述:射频无线杂项 WLAN Synthesizer (RF2 IF) RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
SI4126-F-GMR 功能描述:射频无线杂项 WLAN Synthesizer RF2/IF RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
SI4126M-EVB 功能描述:射频开发工具 802.11b and ISM Band RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V
SI4128DY 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:N-Channel 30-V (D-S) MOSFET
Si4128DY-T1-E3 功能描述:MOSFET 30V 10.9A 5.0W 24mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4128DY-T1-GE3 功能描述:MOSFET 30V 10.9A 5.0W RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube